Data Connect DSP19.2 Guida Utente Pagina 33

  • Scaricare
  • Aggiungi ai miei manuali
  • Stampa
  • Pagina
    / 41
  • Indice
  • SEGNALIBRI
  • Valutato. / 5. Basato su recensioni clienti
Vedere la pagina 32
Gyro Control Unit (GCU)
User’s Guide
33
MaxMetrix, Scottsdale, AZ
PN: GCU-2K1-UG:RevI.2 NGC
4.1.6.3 NO-OP
The NO-OP (no operation) command button tests the communications link with the microcontroller on the
GCU. If the link is valid a message is displayed indicating the link PASSED. If the application is unable
to establish communications with the GCU unit the message displays FAILED.
4.1.6.4 DSP ENTRY POINT
The DSP Entry Point Text Box sets the starting address for the DSP Code. “AUTO” automatically finds
the address in the object code file. The User can specify this address manually if desired.
4.1.6.5 AUTOBOOT ENABLE
The Auto-boot enable checkbox allows the user to disable/enable the microcontroller autoboot function.
During normal operation, if the microcontroller does not get a good status reply from the DSP it will try
and reboot the DSP from FLASH continuously. During Debug the autoboot function conflicts with the
DSP in-circuit emulator. Disabling the autoboot enable function (by unchecking autoboot) disables the
microcontroller from rebooting the DSP, allowing the debug session to resume normally. The autoboot
function should be enabled for normal operation.
4.1.6.6 FIRMWARE RELEASE LEVEL
The firmware revision numbers can be determined using the Status Report selection radio button located on
the Cal/Status Tab. The current revision information is reported back to the GUI for inspection.
4.1.6.7 TROUBLESHOOTING THE LINK
7
There are several reasons for the communications link to report a “FAILED” message, some of the most
common are provided below:
• Power not applied to the GCU unit, power must be applied to download a GCU module.
• Wrong serial port selected. The USB is used as a virtual serial communication port. Make sure
the correct port is selected in the PORTS pull down menu.
• Wrong USB cable type or cable not connected
7
The user should always test the communications link by selecting the NO-OP command button and
getting a PASSED message before trying to download the GCU with new firmware.
Vedere la pagina 32
1 2 ... 28 29 30 31 32 33 34 35 36 37 38 39 40 41

Commenti su questo manuale

Nessun commento

American Dryer Corp. AD-20 manuels

Manuels d'utilisation et guides de l'utilisateur pour Séchoirs American Dryer Corp. AD-20.
Nous fournissons des manuels en pdf 1 American Dryer Corp. AD-20 à télécharger gratuitement par type de document : Manuel de l'utilisateur






Plus de produits et de manuels pour Séchoirs American Dryer Corp.

Modèles Type de document
MDG75MNV Manuel de l'utilisateur   American Dryer Corp. MDG75MNV User Manual, 50 pages
ML-130 II Manuel de l'utilisateur   American Dryer Corp. ML-130 II User Manual, 59 pages
AD-75D II Manuel de l'utilisateur   American Dryer Corp. AD-75D II User Manual, 50 pages
AD/ML-310 Manuel de l'utilisateur   American Dryer Corp. AD/ML-310 User Manual, 54 pages
Phase 7 OPL with S.A.F.E. Gas DSI AD-78 IV Manuel de l'utilisateur   American Dryer Corp. Phase 7 OPL with S.A.F.E. Gas DSI AD-78 IV User Manual, 55 pages
ADG-758 Manuel de l'utilisateur   American Dryer Corp. ADG-758 User Manual, 63 pages
ML-130 III Manuel de l'utilisateur   American Dryer Corp. ML-130 III User Manual, 28 pages
ADG-50DS Manuel de l'utilisateur   American Dryer Corp. ADG-50DS User Manual, 54 pages
AD-400 Manuel de l'utilisateur   American Dryer Corp. AD-400 User Manual, 51 pages
30 lb. Stacked Models Manuel de l'utilisateur   American Dryer Corp. 30 lb. Stacked Models User Manual, 26 pages
AD-385 Manuel de l'utilisateur   American Dryer Corp. AD-385 User Manual, 68 pages
AD-100 Manuel de l'utilisateur   American Dryer Corp. AD-100 User Manual, 61 pages